Marine electronics
Garmin trolling motor calibration
- About 10 minutes on the water
- Compass, then bow offset
- Paired to your Garmin chartplotter
Our own film: Zak calibrates a Force Kraken on the water, from the remote and from the chartplotter.
A trolling motor that has not been calibrated does not know which way the boat is pointing. Anchor lock wanders, heading hold hunts back and forth, and the motor fights you. The fix takes about ten minutes in open water, and you can do it yourself.
When a Garmin trolling motor needs calibrating
- It is new, or was just installed. The compass in the motor has never seen your boat.
- It was moved to another boat, or the mount was moved on this one.
- Anchor lock drifts or circles instead of holding the spot.
- Heading hold steers a few degrees off the line you set.
- You added something magnetic near the bow, such as a speaker, an anchor or a windlass.
Before you start
Pick calm, open water with room to turn a full circle. Stay away from docks, bridges, steel bulkheads and other boats, because a large piece of metal nearby throws the compass off while it is learning. Deploy the motor, make sure the remote is paired and charged, and have your Garmin chartplotter on if you run one.
The calibration, step by step
- Deploy the motor and power it on. Let it get a GPS fix before you do anything else.
- Open the calibration menu on the remote. It is in the trolling motor's settings.
- Calibrate the compass. Start it and follow the prompt on the remote. You turn the boat through a slow, steady circle while the screen counts up to 100 percent. Slow and smooth is what makes it accurate.
- Set the bow offset. Point the motor straight ahead, in line with the keel, and save it. This tells the motor where the front of your boat is, which matters because very few motors are mounted dead center.
- Check it on the chartplotter. With the motor paired to your Garmin, the same calibration is under the trolling motor menu, and the motor shows up on your chart.
- Test it. Set anchor lock and watch it hold. Then set a heading and see that the boat tracks straight.
If it still will not hold
Run the compass calibration again somewhere with more open water around you. If anchor lock overshoots and swings back, turn the anchor lock gain down a step. If it is slow to react in wind or current, turn it up. If it still wanders after that, the motor may be sitting too close to something magnetic, or it is not getting clean power, and that is a rigging question more than a settings one.
What we do when we set one up
- Mount it and wire it properly. Correct wire size, a breaker at the battery, and a clean run to the bow.
- Pair it to your chartplotter and the remote.
- Update the software on the motor and the chartplotter, so the two agree.
- Calibrate it on the water, compass and bow offset, and test anchor lock before the boat goes home.
- Show you how to use it. Ten minutes with the remote in your hand saves a season of guessing.
How it's quoted
We quote it the same day you ask. The number depends on the boat and what is already rigged, and the service writer confirms it with you before any work begins.
Questions we get
How often does a Garmin trolling motor need calibrating?
Once after it is installed, and again any time it is moved, the mount is changed, or you add something magnetic near the bow. It does not need doing every season if it is holding well.
Can I calibrate a Garmin trolling motor at the dock?
No. The compass calibration needs the boat to turn a full circle in open water, away from large pieces of metal such as docks, bridges and steel bulkheads.
Do I need a Garmin chartplotter to calibrate it?
No. The remote does the whole thing. Pairing the motor to a Garmin chartplotter adds control from the screen and puts the motor on your chart.
Why does my anchor lock drift after calibrating?
Usually the calibration was done too close to a dock or a bridge, or the bow offset was never set. Redo both in open water, then adjust the anchor lock gain.
Yamaha Marine Service Pro Elite dealer in Selbyville, serving Ocean City and all of Delmarva. 💬 Ask the assistant or call (302) 436-1737.
Related
From the shop floor
Zak Smith, Yamaha Master Technician, on this.

